How To Start A Flooded Stihl Chainsaw

1. Home
2. Cut Firewood
3. Flooded Chainsaw

How To Start A Flooded Chainsaw

This mail service may comprise affiliate links so I earn a committee.

If you lot need to acquire how to start a flooded chainsaw, don't worry, you're not lone.

In fact, many of u.s.a. who apply weed whips, dirt bikes, older vehicles, or any piece of equipment that contains a carburetor have experienced a flooded engine.

Unfortunately, flooding an engine is pretty easy to exercise.

However, the good news is that it's as well really easy to fix!

For starters (see the pun at that place?) let'southward look at how the engine became flooded to begin with, and and then I'll show you a couple of actually easy ways to go your chainsaw up and running again.

What Causes A Chainsaw To Flood Out?

A flooded chainsaw is caused past too much fuel within the engine which does not allow the fuel to ignite.

Think of it this way, combustion inside an engine needs fuel and air.

By having too much fuel, there'southward not plenty room the for proper air mixture when the spark plug tries to ignite the gas.

Since the spark plug can't ignite the gas without air, you're left pulling the starter string on your chainsaw over and over without information technology e'er starting.

Another indication of a flooded chainsaw is the strong odor of gasoline coming from the saw.

How did y'all chainsaw get flooded in the get-go place?

Chances are y'all flooded the saw by over choking it.

This tin happen by using the choke without having the saw in the run position, or by using the choke on a warmed-up engine when it'southward non really needed.

Some chainsaws, like my Husqvarna 345 for instance, automatically switches to the run position when I pull out the choke lever.

This is a overnice feature that helps eliminate some user error, but not every chainsaw or modest engine is equipped this way.

Also, if you lot have been using your chainsaw for a while and then shut it off, you don't need to choke it in lodge for it to showtime support since the engine is withal warm.

This will cause information technology to inundation.

How To Unflood A Chainsaw Then It Volition Commencement

If you have a flooded chainsaw, yous have a few options that work actually well, and volition get your saw running again without also much attempt.

Hither are the 3 of the easiest ways to start a chainsaw that has been flooded:

Let The Fuel Evaporate

The first option is the easiest since it doesn't crave any endeavour on your part, information technology merely takes time.

Many people wonder if a flooded chainsaw will fix itself?

The answer is yes, but non ever.

Past letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.

This method can have mixed results since the outside air temperature tin play a function in how speedily the fuel evaporates.

Sometimes on a severely flooded engine, y'all tin can let information technology sit for multiple days and it yet won't start, and so although this method is the easiest, it doesn't always piece of work.

Only remember when attempting to start the engine after it has sabbatum for twenty minutes, make sure your choke is Not on.

You lot'll desire to pull the starter rope with the choke off several times which should cause the chainsaw to outset.

Starting A Flooded Engine With No Tools

The 2nd selection is my favorite style to first a flooded chainsaw and I believe information technology'southward the easiest and near constructive way.

The first step is to engage the chain restriction and identify the saw on the ground.

With the choke in the off position (no choke) kneel downwardly and identify i knee over the powerhead of the saw.

This keeps the saw firmly on the basis while keeping both hands free.

Using 1 paw, fully depress the throttle lever while pulling the starter rope 15-20 times with your other free hand.

I typically like to take my right articulatio genus and place it on the saw, while using my left paw to hold down the throttle and my right hand to pull the starter rope.

Although it is somewhat exhausting, by the time you pull the starter rope about xv-20 times your saw will start.

This method creates a lean mixture of fuel by having full throttle with no choke.

It's also a popular fashion to kickoff older vehicles where you'll need to press the gas peddle all the way to the floor and crank the engine several times until it starts.

Starting A Flooded Engine By Removing The Spark Plug

The last way to started a flooded chainsaw involves removing the spark plug.

Kickoff by making certain your chainsaw is in the off position.

Next, remove the condom boot from the spark plug and remove the spark plug from your chainsaw using your scrench.

Do not reinstall the prophylactic kicking to the spark plug equally the plug could ignite the gas inside the saw.

Place the spark plug away from the saw and turn the saw upside down.

While property the saw upside down, take your gratuitous hand and slowly pull the starter rope on the chainsaw.

As you pull the starter rope, the chainsaw volition push the gas out of the cylinder.

Do this about 4 or 5 times until all of the gas has been removed.

Next, take a dry textile and wipe off any gas that's on the spark plug.

Since the engine was flooded, you should notice excess gas on the end of the spark plug that volition need to be removed before it's reinstalled.

Finally, reinstall the spark plug and boot, identify the choke in the off position with the saw on run and start your saw.

Starting A Flooded Chainsaw - Overall

If you've accidentally flooded your chainsaw, you don't have to miss an entire day of cutting firewood.

Simply use ane of the simple steps outline higher up and your chainsaw will exist running again without much effort, and it just takes a few minutes of your time.

Source: https://www.firewood-for-life.com/flooded-chainsaw.html

Share this post